While doing a bit of net surfing today, I ran across some structural tests on the adhesive that I am using, Titebond III.
On balance, all the test results were not conclusive either way. But "not conclusive either way" is not good enough for an airplane.
So, I will be changing adhesives. It appears that there is little choice but to move to T-88, an epoxy adhesive with all the strengths, and difficulties, of epoxy. It also means that I will scrapping the ribs I have built so far.
Bummer.
Friday, September 28, 2012
Saturday, September 22, 2012
Gluing, Gluing, Gluing
I spent 3.5 hours in the shop today. I confirmed an important safety lesson. There is a theory that attempting to hold a very small part, with your finger tips, against the belt sander fence is almost guaranteed to result in considerable pain and bloodshed. But part of my brain was not satisfied with theory and was determined, in the absence of empirical evidence, to go ahead with the attempt. I am pleased (well, "pleased" is not exactly the best word) to report that the theory works out perfectly in practical application.
I have here a photo of a gusset glued up and ready to install.
This view also shows the bit of business card I use to spread the glue and the razor blade whose function is to scrape the parts prior to gluing. The objective of the scraping is to remove oxidation, grime and what-have-you that accumulates on the wood surface and can weaken the glued joint.
The reason the entire back side of the gusset is spread with glue has to do with the need to seal the wood parts against moisture. Once all of the wood parts are fabricated and generally assembled, they will be treated with a high quality spar varnish. However, getting to the backside of the gussets with the varnish will be essentially impossible. So, a layer of glue is applied to the entire back side, thereby sealing that side of the gusset.
The next photo shows the gusset stapled in place.
The number of staples used for any particular joint depends on how well the gusset snuggles down onto the cap strip. I try to use the minimum number of staples possible in order to make the job of pulling them out easier. Yes, the staples are removed once the glue has dried.
There has been considerable discussion within the Wag Builders Yahoo Group, resulting from confusion on my part, regarding the number and location of reinforcing blocks to be installed on the #1 rib for the purpose of attaching the wing root fairings.
After much poking around, photographing Piper rag airplanes, and just plain scratching my tummy, I came up with an approach. The following photo shows the 1"X1" blocks that I have installed.
Though the plans call for only 5 of these blocks, it is not made clear whether that is 5 per rib, or 5 total. In any event, 5 does not appear to be enough. There are actually 14 per rib on my airplane. Is that the right answer? I don't know. One of the challenges of building from plans is that there will be problems that require solutions before one has a complete grasp of the problem. This is one of those situations. We will find out if it is the right answer when it comes time install the wing root fairings.
I have here a photo of a gusset glued up and ready to install.
This view also shows the bit of business card I use to spread the glue and the razor blade whose function is to scrape the parts prior to gluing. The objective of the scraping is to remove oxidation, grime and what-have-you that accumulates on the wood surface and can weaken the glued joint.
The reason the entire back side of the gusset is spread with glue has to do with the need to seal the wood parts against moisture. Once all of the wood parts are fabricated and generally assembled, they will be treated with a high quality spar varnish. However, getting to the backside of the gussets with the varnish will be essentially impossible. So, a layer of glue is applied to the entire back side, thereby sealing that side of the gusset.
The next photo shows the gusset stapled in place.
The number of staples used for any particular joint depends on how well the gusset snuggles down onto the cap strip. I try to use the minimum number of staples possible in order to make the job of pulling them out easier. Yes, the staples are removed once the glue has dried.
There has been considerable discussion within the Wag Builders Yahoo Group, resulting from confusion on my part, regarding the number and location of reinforcing blocks to be installed on the #1 rib for the purpose of attaching the wing root fairings.
After much poking around, photographing Piper rag airplanes, and just plain scratching my tummy, I came up with an approach. The following photo shows the 1"X1" blocks that I have installed.
Though the plans call for only 5 of these blocks, it is not made clear whether that is 5 per rib, or 5 total. In any event, 5 does not appear to be enough. There are actually 14 per rib on my airplane. Is that the right answer? I don't know. One of the challenges of building from plans is that there will be problems that require solutions before one has a complete grasp of the problem. This is one of those situations. We will find out if it is the right answer when it comes time install the wing root fairings.
Routine
Well, hopefully, it is back to routine life. I hope to work a bit on the Traveler today. But the Alvord trip seems to keep on giving. All who attended are still excited about the event. It was definitely a high point adventure for me. One last shot...here is a photo taken of my arrival.
After a final leg of flight, from Burns, Oregon to the Alvord Desert, the landing was picture perfect. I was definitely paying attention to the landing on the dry lake bed. It is a bit tricky. But I pulled it off as if I had been doing it all my life.
Back to the shop!
After a final leg of flight, from Burns, Oregon to the Alvord Desert, the landing was picture perfect. I was definitely paying attention to the landing on the dry lake bed. It is a bit tricky. But I pulled it off as if I had been doing it all my life.
Back to the shop!
Monday, September 17, 2012
Alvord
I promised photos of the Alvord Desert fly-in. It was a great adventure, made more so by learning that my airplane has a performance problem not obvious in low-altitude flying.
These are not in any kind of order.
These are not in any kind of order.
Monday, September 10, 2012
Baby Steps
I promised to make some effort to keep something on the blog through the process of fabricating wing ribs. It is, as I said, a highly repetitive process.
Plus, there have been quite a few demands on my time and I haven't spent the time in the shop that I have wanted. Still, on Sunday afternoon I was able to sneak into the shop and get a rib built.
One other adventure that has been slowing work is preparation for the annual Alvord Desert flyin by a bunch of 150 guys here on the west coast. The flyin is completely casual with no organization except the selection of a date. The weekend of 9/15 this year. This will be the first year I have been able to attend, and I am very much looking forward to it.
The Alvord Desert is located in southeastern Oregon. There is nothing there. The flyin is to the dry lake bed that comprises most of the desert (yes, there is desert in Oregon). The weekend is a camping event, but it is completely primitive. There are no facilities beyond some ramshackle buildings around a hot springs and a pipe installed in one cold spring.
I will post photos on this blog and the 46Juliet blog.
Plus, there have been quite a few demands on my time and I haven't spent the time in the shop that I have wanted. Still, on Sunday afternoon I was able to sneak into the shop and get a rib built.
One other adventure that has been slowing work is preparation for the annual Alvord Desert flyin by a bunch of 150 guys here on the west coast. The flyin is completely casual with no organization except the selection of a date. The weekend of 9/15 this year. This will be the first year I have been able to attend, and I am very much looking forward to it.
The Alvord Desert is located in southeastern Oregon. There is nothing there. The flyin is to the dry lake bed that comprises most of the desert (yes, there is desert in Oregon). The weekend is a camping event, but it is completely primitive. There are no facilities beyond some ramshackle buildings around a hot springs and a pipe installed in one cold spring.
I will post photos on this blog and the 46Juliet blog.
Subscribe to:
Posts (Atom)